Free Shipping In All Countries
Panier 0
7S 80A/100A BMS New Lithium Ion Smart PCM With Android Bluetooth APP UART Correspondence Software (PC) Monitor

7S 80A/100A BMS New Lithium Ion Smart PCM With Android Bluetooth APP UART Correspondence Software (PC) Monitor

Prix régulier $89.99 Prix réduit $204.99 Prix unitaire par
Taxes incluses. Frais de port calculés à la caisse.

 

Note: this BMS with balance function. your battery need matching, battery should have good consistency, if not sure, please use new brand battery. 

 

UART to USB module   or Bluetooth  should use together with the board.

UART to USB module connect to PC by USB, so you can monitor the board, and set the parameter.

Bluetooth module can connect to smart phone,  right now only support android 4.3 above.

APP support english

 

Features

1)Smart BMS with app & laptop controlling;
2) Balance & Balance display;
3) Mulit Temperature switches);
4) MOS transistor can control the battery charge and discharge;
5) low standby current consumption.
6) with UART interface, Bluetooth interface, support PC or smart phone.
7) over charge and over discharge can set by software( APP).
 
Parameter can set by software(APP).
Balance current: 50mA 
Charge voltage: 4.2V * 10 = 42V
SIZE:150*102*17MM
 
Adjustable Parameters:
 
1.Balance voltage setup: Balance voltage Range:  3.3-4.2V 
2.Over-voltage voltage setup: Charge voltage Range :   3.6-4.3V
3.Under-voltage voltage setup: Discharge voltage Range :  2.0-3.3V 
4.Over Charge/Discharge current Setup....
 
Reference Battery Show  by PC or Smart phone :
 
Smart-BMS-1_06
Smart-BMS-1_05
Smart-BMS-1_07
 
 
1-1_05
wire-diagram
 
 

 

 

 

6-10SSMARTDIAGRAM

 

 

 

 

1. Battery assembly notice before BMS installation:

Each cell must match well before BM installation (Battery internal resistance differences within 5 Milliohm, voltage within 0.03 V , capacity vary within 50 mAh). Lfepo4 cell, voltage between 2.6V~3.5V,Li-ion cell, voltage between 3~4V.

If the cells are full charged,please discharge them to the standard voltage range.Cell first parallel then series.

2. Connection instruction of BMS wires:

(a) Connect B- big short wire to battery general negative end( If B-and Discharge port with multi-holes, you can use one large wire to connect one hole or several middle wires to connect each hole.)

(b) Connect signal/Balance wires: remove the balance wires from BMS before you assembly. Start from B-, first wire connect to B-,the second balance B1 wire connect to the first cell positive, B2 connect to second cell positive,balance wires soldering should be according to the order of B-,B1,B2,B3....B7

(c) Make sure all of the wires correct before you plug the connector into BMS:use multi meter to test each neighbouring series voltage ,if not, the BMS will burn.( Li-ion voltage less then 4V,Lifepo4 voltage less than 3.5V)

(d) Test the battery general negative voltage between battery general positive whether equal the total voltage.

(e) Plug the balance wires to BMS(plug low bit to high bit), Connect Charge /Discharge large wires to “ C-” Connect red big wire to battery general positive end. Test the discharge total voltage again.

 

 

 

S-version-wires-instruction


Origin: CN(Origin)
Condition: New
Type: Voltage Regulator
Model Number: PCM-7S100100LIST150
Application: 3.7v li-ion battery
Operating Temperature: -40-85
Supply Voltage: 42v
Dissipation Power: 50
Package: TQFP
is_customized: Yes


Partager ce produit